PTH03000WAD【PDF 2/13 页】MODULE PIP 3.3VIN 6A ADJ T/H

您好，
买卖IC网欢迎您。
请登录
免费注册

1页 [2页]3页 4页 5页 6页

PTH03000W —3.3-V Input

6-A, 3.3-V Input Non-Isolated

Wide-Output Adjust Power Module

Ordering Information

Output Voltage (PTH03000 H xx)

Package Options (PTH03000x HH ) (1)

SLTS200C – MAY 2003 – REVISED DECEMBER 2003

Code

W

Voltage

0.9 V – 2.5 V (Adjust)

Code

AH

Description

Horiz. T/H

Pkg Ref.

(EUS)

(2)

AS

SMD, Standard (3)

(EUT)

Notes: (1) Add “T” to end of part number for tape and reel on SMD packages only.

(2) Reference the applicable package reference drawing for the dimensions and PC board layout

(3) “Standard” option specifies 63/37, Sn/Pb pin solder material.

Pin Descriptions

Vin: The positive input voltage power node to the mod-

ule, which is referenced to common GND.

Vout: The regulated positive power output with respect

to the GND node.

GND: This is the common ground connection for the

‘V in ’ and ‘V out ’ power connections. It is also the 0 VDC

reference for the ‘Inhibit’ and ‘V o Adjust’ control inputs.

Inhibit: The Inhibit pin is an open-collector/drain negative

logic input that is referenced to GND. Applying a low-

level ground signal to this input disables the module’s

Vo Adjust: A 0.1 W 1 % resistor must be directly connected

between this pin and the GND pin to set the output voltage

to a value higher than 0.9 V. The temperature stability

of the resistor should be 100 ppm/°C (or better). The set

point range for the output voltage is from 0.9 V to 2.5 V.

The resistor required for a given output voltage may be

calculated from the following formula. If left open circuit,

the output voltage will default to its lowest value. For

further information on output voltage adjustment, consult

the related application note.

output and turns off the output voltage. When the Inhibit

control is active, the input current drawn by the regulator

is significantly reduced. If the Inhibit pin is left open-

R set

= 10 k ? ·

0.891 V

V out – 0.9 V

– 4.99 k ?

circuit, the module will produce an output whenever a

valid input source is applied.

The specification table gives the preferred resistor values

for a number of standard output voltages.

For technical support and further information visit http://power.ti.com

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

PTKM10-180SM TOROIDAL POWER CHOKE 10UH SMD

PV37W504C01B00 TRIMMER 500K OHM 0.25W TH

PVC6282 CAP FILM 8200PF 600VDC RADIAL

PVF2A504A11R00 TRIMMER 500K OHM 0.001W SMD

PVM-16V121MG70E-R2 CAP ALUM 120UF 16V 20% SMD

PWR1317AC CONV DC/DC +/-15V +/-50MA DIP

PWR1726AC CONV DC/DC 1.5W UNREG DIP

PWR70C CONV DC/DC 3W 100MA UNREG

相关代理商/技术参数

PTH03000WAH 功能描述:DC/DC转换器 6A 3.3V-In Wide-Out Adj Plug-in Pwr Mdl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

PTH03000WAS 功能描述:DC/DC转换器 6A 3.3V-In Wide-Out Adj Plug-in Pwr Mdl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

PTH03000WAST 功能描述:DC/DC转换器 6A 3.3V-In Wide-Out Adj Plug-in Pwr Mdl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

PTH03000WAZ 功能描述:DC/DC转换器 6A 3.3V-In Wide-Out Adj Plug-in Pwr Mdl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

PTH03000WAZT 功能描述:DC/DC转换器 6A 3.3V-In Wide-Out Adj Plug-in Pwr Mdl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

PTH03010 制造商:ARTESYN 制造商全称:Artesyn Technologies 功能描述:DC-DC CONVERTERS POLA Non-isolated

PTH03010W 制造商:TI 制造商全称:Texas Instruments 功能描述:15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module

PTH03010WAD 功能描述:DC/DC转换器 15A 3.3V-Inp Wide Output Adj Pwr Mdl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: